Antimicrobial Fabric Coating Using Liquid Metal

2022-05-14 23:59:02 By : Mr. xilin Li

We use cookies to enhance your experience. By continuing to browse this site you agree to our use of cookies. More info.

The pressing need for surfaces and fabrics that can be protected against microbes has been laid bare by the Covid-19 pandemic. Research published online in Advanced Materials has presented a method for coating fabrics with a liquid metal to kill any pathogens they come into contact with.

Study: A Liquid Metal Mediated Metallic Coating for Antimicrobial and Antiviral Fabrics . Image Credit: Kolomiiets Iryna/Shutterstock.com

Pathogens can survive for a long time on the fabrics commonly used for bedding, clothing, and face masks in healthcare and community settings. This is especially concerning in hospitals, where outbreaks of drug-resistant superbugs are becoming more widespread.

Additionally, it has been reported that the virus that causes COVID-19 can survive for up to two to three days on fabric. Pathogens can be transmitted from patient to patient after contact with the infected material.

Liquid metal (LM) mediated particles coated on a fabric. a) Fabrication schematics of gallium-copper (LMCu) coatings on fabric. b) Schematics of adhesion of LM particles on the fabric by conformal contact. c) Schematics of galvanic replacement (i–iv) LM particles on fabric with Cu ions. d) SEM images showing LMCu on a single fiber (inset). e–g) Surface characteristics of LMCu coated on a fabric formed by reaction with 1 m CuSO4 solution. e) The surface of the Ga LM particles (cyan) serves as the seed to grow high crystalline (111) Cu (orange) after 10 min. f) The Ga particles (cyan) wet the surface of the adjacent copper crystal (orange). The arrow explains the wetting direction of Ga to make LMCu particles. g) As a result, LMCu particles (red) form on the surface after 1000 min. h) High-resolution transmission electron microscopy (HR-TEM) image and corresponding energy-dispersive X-ray spectroscopy (EDS) elemental maps of the produced LMCu particles, respectively. (Cu (green), Ga (red), and O (blue)). Image Credit: Kwon, K.Y et al., Advanced Materials

Fabric facemasks are deployed to stop the spread of airborne and droplet-spread pathogens by trapping microbes in the fabric. However, whilst the pathogens are trapped, stopping them from infecting the wearer, they are not killed. If proper handling procedures are not followed, the pathogenic microbes can still infect individuals. This is an incredibly common occurrence. Therefore, there is an urgent need for fabrics with antimicrobial coatings.

Currently, there are several strategies to create antimicrobial coatings for fabrics. These include coating them with agents such as polymers, 2D materials, metal particles, and organic-metal frameworks. However, each of these strategies has drawbacks that affect the efficacy of their use as antimicrobial coatings.

For example, copper nanoparticle-coated or impregnated face masks have recently been approved for commercial use. Copper nanoparticles show a broad spectrum of efficacy against viruses, bacteria, and fungi. Additionally, copper is low-cost, presenting a cheap solution to the problem.

However, these coatings can easily fade over time and have issues with adhesion and nonuniform covering. Clearly, in the case of facemasks, this is a major drawback.

Enhanced adhesion of LMCu on fabric. a) Schematic of the peel-off test method. b) Peel-off test results comparing the LMCu coated fabric and spray-coated CuNPs which represent conventional methods of depositing copper on fabrics. A real image of the compression pressure measured from 20 to 100 at 40 kPa intervals. c) Measurement of the amount of Cu buried on the carbon tape compared to the total area quantitative analysis of the peeling test by pressure. d) A schematic of the detachment test through the transient airflow, which simulated respiration systems. e) The degree of particle desorption (top: LMCu, bottom: CuNPs) in response to airflows to represent breathing (1–3 m s−1), sneezing (4 m s−1), and coughing (5 m s−1). f) Quantitative analysis by image processing. Image Credit: Kwon, K.Y et al., Advanced Materials

To overcome these issues, the team behind the research published in Advanced Materials developed a novel process to provide superior antimicrobial coatings for fabrics. The process uses liquid metal to mediate the deposition of copper nanoparticles onto materials at room temperature.

The process uses liquid gallium particles that act as an adhesion nucleation layer. In the process, copper ions are spontaneously reduced into metallic copper by galvanic replacement. The team termed the new class of particles “LMCu particles” and contain both copper and alloys of gallium and copper.

The first step of the process involved adding a liquid metal particle suspension to the fabric and then evaporating the solvent. Then, the coated nonwoven fabric was immersed in a 1M solution of CuSO4 and the LMCu particles were spontaneously formed. Copper crystals grew on the liquid metal oxides from initial seeds. Carbon, a major component of the material tested, was not detected in the final coating, strongly demonstrating that LMCu particles covered the entire surface of the fabric.

The fabric used in the study was a mixture of 45% polyester and 55% cellulose, although the coating worked well on a range of tested materials. Using scanning electron microscopy, it was found that 3 coatings fully covered the fabric. The particles exhibited enhanced levels of adhesion to the fabric, and this seems to be due to a combination of the “soft” nature of liquid particles and surface oxides that form on gallium.

Furthermore, the LMCu particles have better antiviral, antifungal, and antibacterial properties than pure copper. The unique properties of this class of nanoparticles make them ideal for use as an antimicrobial coating that is far more durable than alternatives on the market currently.

The study presented a facemask design that utilizes gallium and copper-coated materials. There is a danger with conventional copper-based antimicrobial coatings of copper particles becoming detached and entering the respiratory system of the wearer, which could cause health problems. However, the adhesive layer of LMCu particles prevents this, increasing the safety of the coated material whilst providing enhanced antimicrobial protection.

An antimicrobial-coated facemask must also cope with an obvious factor: the wearer breathing. Breath is moist and warm, leading to changes in humidity. The facemasks were evaluated over a range of humidity, displaying the same adhesion properties at both low and high humidity.

They were also evaluated for airflow, considering actions such as breathing, coughing, and sneezing, again displaying superior performance. Delamination tests were carried out by applying pressure and using carbon tape.

Antiviral testing of the LMCu coated fabric. a) Schematic experimental setup and b) Viral titers from LMCu coated fabric were analyzed after 5, 10, 15, and 30 min incubations post-challenge with human Influenza A H1N1 virus inoculum (108 TCID50). The inoculum of 108 TCID50 not exposed to the mask was used as the positive control. Samples were collected after each time point from the front and back of the LMCu coated fabric and sections were frozen and assessed using TCID50 method. Results were analyzed via ANOVA, showing statistically significant differences between positive control and all incubation time points (*** = p < 0.01). Image Credit: Kwon, K.Y et al., Advanced Materials

The study demonstrates a novel antimicrobial coating fabricated by a liquid metal-mediated process. Results of the research showed that this coating has superior adhesive and antipathogenic qualities, paving the way for safer fabrics that will help stop the spread of harmful diseases in the future.

Kwon, K.Y et al. (2021) A Liquid Metal Mediated Metallic Coating for Antimicrobial and Antiviral Fabrics [online] Advanced Materials 33:45 3104298 | onlinelibrary.wiley.com. Available at: https://onlinelibrary.wiley.com/doi/10.1002/adma.202104298

Disclaimer: The views expressed here are those of the author expressed in their private capacity and do not necessarily represent the views of AZoM.com Limited T/A AZoNetwork the owner and operator of this website. This disclaimer forms part of the Terms and conditions of use of this website.

Reg Davey is a freelance copywriter and editor based in Nottingham in the United Kingdom. Writing for News Medical represents the coming together of various interests and fields he has been interested and involved in over the years, including Microbiology, Biomedical Sciences, and Environmental Science.

Please use one of the following formats to cite this article in your essay, paper or report:

Davey, Reginald. (2021, November 17). Antimicrobial Fabric Coating Using Liquid Metal. AZoM. Retrieved on May 14, 2022 from https://www.azom.com/news.aspx?newsID=57355.

Davey, Reginald. "Antimicrobial Fabric Coating Using Liquid Metal". AZoM. 14 May 2022. <https://www.azom.com/news.aspx?newsID=57355>.

Davey, Reginald. "Antimicrobial Fabric Coating Using Liquid Metal". AZoM. https://www.azom.com/news.aspx?newsID=57355. (accessed May 14, 2022).

Davey, Reginald. 2021. Antimicrobial Fabric Coating Using Liquid Metal. AZoM, viewed 14 May 2022, https://www.azom.com/news.aspx?newsID=57355.

Do you have a review, update or anything you would like to add to this news story?

AZoM speaks with Dr. Nicola Ferralis from MIT about his research that has developed a low-cost process of creating carbon fibers from hydrocarbon pitch. This research could lead to the large-scale use of carbon fiber composites in industries that have thus far been limited.

In this interview, AZoM speaks with Marco Enger, Senior Tribologist from GGB, to discuss how nano fillers affect transfer films within tribological systems.

Ahead of their talk on green chemistry and profitability in laboratory research at ChemUK 2022, AZoM spoke with Jacqueline Balian from Gambica and Martyn Fordman from Asynt about encouraging sustainability in the chemical industry.

COXEM's CP-8000+ is a powerful cross section polishing tool that uses an argon ion beam to allow precise, advanced sample preparation. Its state-of-the-art technology means the sample is not deformed and does not suffer any kind of physical damage.

This product profile outlines the Evolution™ Pro UV-Vis Spectrophotometers from Thermo Fisher Scientific.

Extrel’s all-new MAX300-RTG 2.0 is the real-time industrial gas analyzer now redesigned with a touch screen.

This article provides an end-of-life assessment of lithium-ion batteries, focusing on the recycling of an ever-growing amount of spent Li-Ion batteries in order to work toward a sustainable and circular approach to battery use and reuse.

Corrosion is the degradation of an alloy caused by its exposure to the environment. Corrosion deterioration of metallic alloys exposed to the atmosphere or other adverse conditions is prevented using a variety of techniques.

Due to the ever-increasing demand for energy, the demand for nuclear fuel has also increased, which has further created a significant increase in the requirement for post-irradiation examination (PIE) techniques.

AZoM.com - An AZoNetwork Site

Owned and operated by AZoNetwork, © 2000-2022